{
  "meta": {
    "design": "C0 4-lift twin-boom quadplane, v0.4.0 (CAD rev D)",
    "spec": "docs/research/hardware-spec.md",
    "checked": "2026-10-21",
    "units": "mm, N*m, USD",
    "frame": "Same as cad/params.txt: X forward, Y up, Z right. Joint coordinates in the md are local to each part (boom axis = local X, split plane = local y 0).",
    "notes": [
      "Every head dimension is the maximum from the vendor product page (Bolt Depot 'Product details', checked 2026-10-21).",
      "clearance_hole_mm is the ISO 273 normal (H13) value; the printed-part model value is clearance_hole_mm + 0.2 (FDM compensation, see fits FT07).",
      "torque_Nm values marked EST in torque_basis are engineering estimates to be confirmed by measurement item M3 in the md.",
      "qty is per aircraft; order_qty includes spares.",
      "Entries with length_mm marked provisional depend on a part dimension not published (listed in 'unknowns')."
    ]
  },
  "fasteners": [
    {
      "id": "F01",
      "description": "Motor to motor plate (4 lift + pusher), from below through the PA6-CF floor into the motor base",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 8,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 6.5,
        "note": "opens from the boom bore up to the 4.5 mm floor (lift); from the cup interior (pusher)"
      },
      "grip_mm": 5.0,
      "thread_engagement_mm": 3.0,
      "engagement_limit_mm": 3.3,
      "insert": null,
      "nut": null,
      "washer": {
        "id": "W01",
        "standard": "DIN 125-A",
        "size": "M3",
        "od_mm": 7.0,
        "id_mm": 3.2,
        "t_mm": 0.5,
        "qty_per_screw": 1
      },
      "threadlocker": "Loctite 242, one drop on the last 2-3 threads only; keep off the PA6-CF (TDS: not for thermoplastics)",
      "torque_Nm": 0.6,
      "torque_basis": "EST: limited by bearing pressure on the printed floor (F = T/(K d) = 0.6/(0.16 x 0.003) = 1250 N; 41 MPa on the washer). Fastenal A2-70 M3 lubricated max 0.81.",
      "qty": 20,
      "order_qty": 30,
      "joints": [
        "J01 lift motor to motor plate (x4 motors, 4 each)",
        "J12 pusher motor to cup (4)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6379",
      "url": "https://boltdepot.com/Product-Details?product=6379",
      "unit_usd": 0.06,
      "checked": "2026-10-21"
    },
    {
      "id": "F02",
      "description": "Split-clamp screws (motor mounts, tail clamps), stabiliser/fin shoe screws, provisional lift-prop screws",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 16,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 6.5,
        "depth_mm": 5.6,
        "note": "clamp caps; none on fin shoe flange"
      },
      "thread_engagement_mm": 6.0,
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.5,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6
      },
      "nut": null,
      "washer": null,
      "threadlocker": "none (brass insert in plastic); witness mark",
      "torque_Nm": 0.5,
      "torque_basis": "EST: insert torque-out in PETG/PA6-CF not published; confirm >= 2x by coupon test M3",
      "qty": 36,
      "qty_breakdown": {
        "motor mount clamps": 16,
        "tail clamps": 8,
        "stab + fin shoe": 4,
        "lift prop plates (provisional length)": 8
      },
      "order_qty": 50,
      "joints": [
        "J02 motor mount upper/lower clamp (4 per mount x4)",
        "J08 tail clamp to rear stub (4 per side)",
        "J09 fin shoe + stabiliser to tail clamp (2 per side)",
        "J03 lift prop plate to motor hub (2 per motor, provisional)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6382",
      "url": "https://boltdepot.com/Product-Details?product=6382",
      "unit_usd": 0.06,
      "checked": "2026-10-21"
    },
    {
      "id": "F03",
      "description": "Gear clamp split screws",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 20,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 6.5,
        "depth_mm": 15.3
      },
      "thread_engagement_mm": 6.0,
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.5,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6
      },
      "nut": null,
      "washer": null,
      "threadlocker": "none",
      "torque_Nm": 0.5,
      "torque_basis": "EST, as F02",
      "qty": 16,
      "order_qty": 24,
      "joints": [
        "J06 gear clamp halves on boom (4 per clamp x4)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6383",
      "url": "https://boltdepot.com/Product-Details?product=6383",
      "unit_usd": 0.07,
      "checked": "2026-10-21"
    },
    {
      "id": "F04",
      "description": "Boom splice cross-bolts (rear motor mount) and rear boom-clamp bolts to the wing hardpoint",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 40,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 7.5,
        "depth_mm": 5.0,
        "note": "splice: head + washer; rear wing clamp: d 6.5, depth 7.5, no washer"
      },
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.5,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6,
        "applies_to": "rear wing clamp only"
      },
      "nut": {
        "id": "N01",
        "standard": "DIN 985 nylon-insert lock nut",
        "size": "M3",
        "af_mm": 5.5,
        "h_mm": 4.0,
        "pocket_af_mm": 5.7,
        "pocket_depth_mm": 8.0,
        "applies_to": "splice only"
      },
      "washer": {
        "id": "W01",
        "standard": "DIN 125-A",
        "size": "M3",
        "od_mm": 7.0,
        "t_mm": 0.5,
        "qty_per_screw": 1,
        "applies_to": "splice, under head"
      },
      "threadlocker": "none (nylock)",
      "torque_Nm": 0.5,
      "torque_basis": "EST: clamp passes through a printed block and a crush plug; Fastenal A2-70 M3 lubricated max 0.81",
      "qty": 8,
      "qty_breakdown": {
        "splice cross-bolts": 4,
        "rear boom clamp to wing": 4
      },
      "order_qty": 12,
      "joints": [
        "J04 boom splice at rear motor mount (2 per side)",
        "J05b rear boom clamp to wing hardpoint (2 per side)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6387",
      "url": "https://boltdepot.com/Product-Details?product=6387",
      "unit_usd": 0.15,
      "checked": "2026-10-21"
    },
    {
      "id": "F05",
      "description": "Landing-leg retaining cross-bolt through gear clamp and leg",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 30,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 7.5,
        "depth_mm": 4.0,
        "note": "4.0 deep so the head and washer stay outside the leg tube (CAD rev B)"
      },
      "insert": null,
      "nut": {
        "id": "N01",
        "standard": "DIN 985",
        "size": "M3",
        "af_mm": 5.5,
        "h_mm": 4.0,
        "pocket_af_mm": 5.7,
        "pocket_depth_mm": 4.3,
        "note": "pocket 4.3 deep: the nut bears just outside the leg tube; an 8.0 pocket would cut into the leg socket (CAD rev B)"
      },
      "washer": {
        "id": "W01",
        "standard": "DIN 125-A",
        "size": "M3",
        "od_mm": 7.0,
        "t_mm": 0.5,
        "qty_per_screw": 1
      },
      "threadlocker": "none (nylock)",
      "torque_Nm": 0.5,
      "torque_basis": "EST, as F04",
      "qty": 4,
      "order_qty": 8,
      "joints": [
        "J07 landing leg in gear clamp socket (1 per leg)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6385",
      "url": "https://www.boltdepot.com/Product-Details.aspx?product=6385",
      "unit_usd": 0.1,
      "checked": "2026-11-02",
      "cad_change": "hardware-spec J07 gave M3 x 25 with an 8.0 nut pocket in the 34 mm block: the pocket would reach x -9, inside the leg tube (radius 12.7). With the nut outside the tube (bearing at -12.7) and the head seat at +13.0 the screw must be 30 long (CAD rev B, 2026-10-21)."
    },
    {
      "id": "F06",
      "description": "Front boom clamp bolts to the spar-collar hardpoint in the wing",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 35,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 6.5,
        "depth_mm": 4.3
      },
      "thread_engagement_mm": 6.0,
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.5,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6
      },
      "nut": null,
      "washer": null,
      "threadlocker": "none",
      "torque_Nm": 0.5,
      "torque_basis": "EST, as F02",
      "qty": 4,
      "order_qty": 8,
      "joints": [
        "J05a front boom clamp to wing spar collar (2 per side)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6386",
      "url": "https://boltdepot.com/Product-Details?product=6386",
      "unit_usd": 0.15,
      "checked": "2026-10-21"
    },
    {
      "id": "F07",
      "description": "Light-duty screws into inserts: pusher cup radial screws, canopy hatch, pitot clamp, FC tray (provisional)",
      "standard": "ISO 7380-1 button head (vendor lists no standard; dims match)",
      "thread": "M3x0.5",
      "length_mm": 8,
      "head_d_mm": 5.7,
      "head_h_mm": 1.65,
      "drive": "hex socket 2.0 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": null,
      "thread_engagement_mm": 6.0,
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.0,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6
      },
      "nut": null,
      "washer": null,
      "threadlocker": "none",
      "torque_Nm": 0.4,
      "torque_basis": "EST: 2.0 mm thin flanges",
      "qty": 11,
      "qty_breakdown": {
        "pusher cup radial": 4,
        "canopy hatch": 2,
        "pitot clamp pinch": 1,
        "FC tray (provisional)": 4
      },
      "order_qty": 20,
      "joints": [
        "J12 pusher cup to pod tail ring",
        "J13 canopy hatch to pod frame",
        "J16 pitot clamp",
        "J15 FC to tray (provisional)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "7219",
      "url": "https://boltdepot.com/Product-Details?product=7219",
      "unit_usd": 0.06,
      "checked": "2026-10-21"
    },
    {
      "id": "F08",
      "description": "Wing saddle to pod frame",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": 12,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.4,
      "tap_drill_mm": null,
      "counterbore": null,
      "grip_mm": 6.0,
      "thread_engagement_mm": 6.0,
      "insert": {
        "id": "I01",
        "model": "ruthex RX-M3x5.7",
        "hole_d_mm": 4.0,
        "hole_depth_mm": 7.0,
        "od_mm": 4.6,
        "length_mm": 5.7,
        "min_wall_mm": 1.6
      },
      "nut": null,
      "washer": null,
      "threadlocker": "none",
      "torque_Nm": 0.5,
      "torque_basis": "EST, as F02",
      "qty": 4,
      "order_qty": 12,
      "note": "extra 8 cover a shorter lift-prop screw if the measured hub is thin (see F02 provisional)",
      "joints": [
        "J11 wing saddle root-plate flange to pod frame (4)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6381",
      "url": "https://boltdepot.com/Product-Details?product=6381",
      "unit_usd": 0.06,
      "checked": "2026-10-21"
    },
    {
      "id": "F09",
      "description": "Wing panel retention bolt (one per side, 70 % chord, through the saddle bolt pillar and the panel root tongue)",
      "standard": "ISO 7380-1 button head (vendor lists no standard; dims match)",
      "thread": "M5x0.8",
      "length_mm": 25,
      "head_d_mm": 9.5,
      "head_h_mm": 2.75,
      "drive": "hex socket 3.0 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 5.5,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 10.3,
        "depth_mm": 1.0
      },
      "grip_mm": 12.8,
      "insert": null,
      "nut": {
        "id": "N02",
        "standard": "DIN 985 nylon-insert lock nut",
        "size": "M5",
        "af_mm": 8.0,
        "h_mm": 5.0,
        "pocket_af_mm": 8.2,
        "pocket_depth_mm": 11.1
      },
      "washer": null,
      "threadlocker": "none (nylock)",
      "torque_Nm": 0.5,
      "torque_basis": "EST: PETG pillar bearing (F = 0.5/(0.16 x 0.005) = 625 N on 47 mm2 = 13 MPa); rev 2026-11-02 halved from 1.0 N m (27 MPa = 0.68 of the PETG proxy yield, creep risk, STR-13): the bolt carries panel torsion in shear and needs no clamp load; the nylock holds it",
      "qty": 2,
      "order_qty": 6,
      "joints": [
        "J10 wing panel to saddle (1 per side)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6636",
      "url": "https://boltdepot.com/Product-Details?product=6636",
      "unit_usd": 0.21,
      "checked": "2026-11-02",
      "cad_change": "rev E (2026-11-01): M5 x 25 with the nut pocket 11.1 mm deep (cad/params.txt pillarNutDepth, computed by cad/params.mjs from the wing thickness, 11.0 before the 2026-11-02 aero/sizing loop closure; pocket_depth_mm above mirrors it and is checked by MFG-04). Bolt Depot 6635 is M5 x 20 and never reaches the nylock in the 11.1 mm pocket: do not order it."
    },
    {
      "id": "F10",
      "description": "Servo mounting screws (provisional: servo tab hole size and spacing not published)",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M2x0.4",
      "length_mm": 10,
      "head_d_mm": 3.98,
      "head_h_mm": 2.0,
      "drive": "hex socket 1.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 2.4,
      "tap_drill_mm": null,
      "counterbore": null,
      "insert": null,
      "nut": {
        "id": "N03",
        "standard": "DIN 934 hex nut",
        "size": "M2",
        "af_mm": 4.0,
        "h_mm": 1.6,
        "pocket_af_mm": 4.2,
        "pocket_depth_mm": 2.0
      },
      "washer": null,
      "threadlocker": "none",
      "torque_Nm": 0.15,
      "torque_basis": "EST: snug against servo rubber grommets/tabs; no published value",
      "qty": 20,
      "order_qty": 30,
      "joints": [
        "J14 servo to printed servo tray (4 per servo x5)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "6365",
      "url": "https://boltdepot.com/Product-Details?product=6365",
      "unit_usd": 0.12,
      "checked": "2026-10-21"
    },
    {
      "id": "F11",
      "description": "Control-horn screws (supplied with the horn kit, kit item 7)",
      "standard": "— (supplier states M2x14 only)",
      "thread": "M2x0.4",
      "length_mm": 14,
      "head_d_mm": null,
      "head_h_mm": null,
      "drive": "—",
      "material": "—",
      "clearance_hole_mm": 2.4,
      "tap_drill_mm": null,
      "insert": null,
      "nut": {
        "id": "N03",
        "standard": "DIN 934 hex nut",
        "size": "M2",
        "af_mm": 4.0,
        "h_mm": 1.6,
        "pocket_af_mm": 4.2,
        "pocket_depth_mm": 2.0
      },
      "washer": null,
      "threadlocker": "none (nylon horn)",
      "torque_Nm": 0.15,
      "torque_basis": "EST: snug; nylon horn base",
      "qty": 10,
      "order_qty": 0,
      "joints": [
        "J17 horn to aileron hardpoint (2 per horn x2)",
        "J17 horn through elevator and rudders with kit backplate (2 per horn x3)"
      ],
      "vendor": "Amazon (kit item 7)",
      "part_no": "B0B58ZSC8J",
      "url": "https://www.amazon.com/dp/B0B58ZSC8J",
      "unit_usd": 0.0,
      "checked": "2026-10-21"
    },
    {
      "id": "F12",
      "description": "Lift prop clamp-plate screws: length = 2.5 (plate) + hub thickness (—) + 5.0 engagement, max engagement 8.0 (maker drawing). Order covered by F02/F08 lengths.",
      "standard": "ISO 4762 (DIN 912)",
      "thread": "M3x0.5",
      "length_mm": null,
      "length_provisional_mm": 16,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm",
      "material": "A2 (18-8) stainless",
      "clearance_hole_mm": 3.2,
      "tap_drill_mm": null,
      "insert": null,
      "nut": null,
      "washer": null,
      "threadlocker": "Loctite 242 on the screw tip (metal into motor hub)",
      "torque_Nm": 0.8,
      "torque_basis": "Fastenal A2-70 M3 lubricated 0.81 N*m (K 0.16); threadlocker acts as lubricant",
      "qty": 8,
      "order_qty": 0,
      "joints": [
        "J03 JeeFly 1755 prop to X4110S hub (2 of the 4 M3 holes on the 12 mm circle)"
      ],
      "vendor": "Bolt Depot (from F02 or F08 stock)",
      "part_no": "6382 / 6381",
      "url": "https://boltdepot.com/Product-Details?product=6382",
      "unit_usd": 0.0,
      "checked": "2026-10-21"
    },
    {
      "id": "F13",
      "description": "Pusher M6 bolt-on adapter to the X4110S hub: 4 screws supplied with the motor (maker drawing View A-A, dia 3.2 / dia 5.7 counterbores on dia 12). Length not published: 8 mm EST in the CAD (flange 5.0 EST, counterbore 3.0, engagement 6.0 < 8.0 limit)",
      "standard": "— (supplied; ISO 4762 geometry assumed in the CAD)",
      "thread": "M3x0.5",
      "length_mm": 8,
      "head_d_mm": 5.68,
      "head_h_mm": 3.0,
      "drive": "hex socket 2.5 mm (EST)",
      "material": "— (supplied)",
      "clearance_hole_mm": 3.2,
      "tap_drill_mm": null,
      "counterbore": {
        "d_mm": 5.7,
        "depth_mm": 3.0,
        "note": "in the adapter flange (maker drawing)"
      },
      "insert": null,
      "nut": null,
      "washer": null,
      "threadlocker": "Loctite 242 (metal to metal)",
      "torque_Nm": 0.8,
      "torque_basis": "as F12 (Fastenal A2-70 M3 lubricated 0.81)",
      "qty": 4,
      "order_qty": 0,
      "joints": [
        "J03b adapter to pusher hub (4)"
      ],
      "vendor": "SunnySky (in motor box)",
      "part_no": "—",
      "url": "https://cdn.shopify.com/s/files/1/2024/0305/files/X4110S.jpg?v=1553581346",
      "unit_usd": 0.0,
      "checked": "2026-10-21"
    }
  ],
  "nuts": [
    {
      "id": "N01",
      "standard": "DIN 985 nylon-insert lock nut (vendor: hex nylon insert lock nut)",
      "thread": "M3x0.5",
      "af_mm": 5.5,
      "h_mm": 4.0,
      "material": "A2 (18-8) stainless",
      "qty": 8,
      "order_qty": 16,
      "joints": [
        "J04 splice cross-bolts (4)",
        "J07 leg cross-bolts (4)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "4792",
      "url": "https://boltdepot.com/Product-Details?product=4792",
      "unit_usd": 0.07,
      "checked": "2026-10-21"
    },
    {
      "id": "N02",
      "standard": "DIN 985 nylon-insert lock nut",
      "thread": "M5x0.8",
      "af_mm": 8.0,
      "h_mm": 5.0,
      "material": "A2 (18-8) stainless",
      "qty": 2,
      "order_qty": 6,
      "joints": [
        "J10 wing bolts"
      ],
      "vendor": "Bolt Depot",
      "part_no": "4794",
      "url": "https://boltdepot.com/Product-Details?product=4794",
      "unit_usd": 0.09,
      "checked": "2026-10-21"
    },
    {
      "id": "N03",
      "standard": "DIN 934 hex nut",
      "thread": "M2x0.4",
      "af_mm": 4.0,
      "h_mm": 1.6,
      "material": "A2 (18-8) stainless",
      "qty": 30,
      "order_qty": 100,
      "joints": [
        "J14 servo screws (20)",
        "J17 horn screws (10)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "7362",
      "url": "https://boltdepot.com/Product-Details?product=7362",
      "unit_usd": 0.0221,
      "pack_usd": 2.21,
      "checked": "2026-10-21"
    },
    {
      "id": "N04",
      "standard": "M6x1.0 bullet (acorn) prop nut, supplied with motor",
      "thread": "M6x1.0",
      "af_mm": null,
      "h_mm": 19.5,
      "material": "—",
      "qty": 1,
      "order_qty": 0,
      "joints": [
        "J03b pusher prop on M6 adapter"
      ],
      "vendor": "SunnySky (in motor box)",
      "part_no": "—",
      "url": "https://cdn.shopify.com/s/files/1/2024/0305/files/X4110S.jpg?v=1553581346",
      "unit_usd": 0.0,
      "checked": "2026-10-21"
    }
  ],
  "washers": [
    {
      "id": "W01",
      "standard": "DIN 125 (vendor)",
      "size": "M3",
      "od_mm": 7.0,
      "id_mm": 3.2,
      "t_mm": 0.5,
      "material": "A2 (18-8) stainless",
      "qty": 28,
      "order_qty": 100,
      "joints": [
        "J01/J12 motor screws (20)",
        "J04/J07 cross-bolt heads (8)"
      ],
      "vendor": "Bolt Depot",
      "part_no": "4513",
      "url": "https://boltdepot.com/Product-Details?product=4513",
      "unit_usd": 0.0145,
      "pack_usd": 1.45,
      "checked": "2026-10-21"
    }
  ],
  "inserts": [
    {
      "id": "I01",
      "model": "ruthex RX-M3x5.7",
      "thread": "M3",
      "od_mm": 4.6,
      "length_mm": 5.7,
      "hole_d_mm": 4.0,
      "hole_depth_min_mm": 7.0,
      "min_wall_mm": 1.6,
      "boss_od_min_mm": 8.0,
      "material": "brass, lead free",
      "qty": 67,
      "order_qty": 100,
      "qty_breakdown": {
        "motor mounts": 16,
        "tail clamps": 8,
        "stab/fin": 4,
        "gear clamps": 16,
        "wing hardpoints": 8,
        "pusher cup": 4,
        "saddle to pod": 4,
        "canopy": 2,
        "pitot": 1,
        "FC tray": 4
      },
      "vendor": "Amazon (ruthex)",
      "part_no": "B08BCRZZS3",
      "url": "https://www.amazon.com/dp/B08BCRZZS3",
      "unit_usd": 0.0999,
      "pack_usd": 9.99,
      "checked": "2026-10-21",
      "sources": [
        "hole 4.0 mm and length 5.7 mm: ruthex comparison table on https://www.amazon.com/dp/B08K1BVGN9 (checked 2026-10-21)",
        "OD 4.6 mm, min wall 1.6 mm: https://3djake.com/ruthex/threaded-insert-m3-100-pieces (search snippet, 2026-10-21)",
        "hole depth = length + >= 1.3 mm: EST rule, cf. JLC3DP M4x8 insert -> 10 mm hole, https://jlc3dp.com/help/article/threaded-insert-service"
      ]
    }
  ],
  "consumables": [
    {
      "id": "C01",
      "item": "Loctite 242 blue threadlocker 6 ml",
      "use": "metal-to-metal threads only: F01 motor screws, F12 prop screws",
      "vendor": "Amazon",
      "part_no": "B000I1RSNS",
      "url": "https://www.amazon.com/dp/B000I1RSNS",
      "unit_usd": 7.03,
      "checked": "2026-10-21"
    }
  ],
  "fits": [
    {
      "id": "FT01",
      "joint": "Wing joiner 0.875 x 0.058 in in spar socket 1.000 x 0.058 in",
      "nominal_mm": 22.225,
      "hole": {
        "nominal_mm": 22.454,
        "tol_mm": [
          -0.203,
          0.203
        ]
      },
      "shaft": {
        "nominal_mm": 22.225,
        "tol_mm": [
          -0.102,
          0.102
        ]
      },
      "min_clearance_mm": -0.076,
      "max_clearance_mm": 0.534,
      "nominal_clearance_mm": 0.229,
      "action": "measure every tube on receipt (M1); if tight, lap the joiner with 400-grit; if > 0.30 mm, shim with one wrap of packing tape",
      "source": "OD +-0.004 in, wall +-0.002 in (Zoro listing for 1.000 x 0.035 6061-T6 drawn tube, search 2026-10-21; same tolerance assumed for 0.875 and 0.058 wall, EST); ID tol = OD tol + 2 x wall tol (calc). Alcobra lists +-0.008 in for 5/8-1 in OD (https://alcobrametals.com/?p=91925): if that applies the band doubles. ASTM B210 table not accessed (—)."
    },
    {
      "id": "FT02",
      "joint": "1.000 in boom in printed split clamp bore (motor mounts, boom clamps, gear clamps, tail clamps)",
      "nominal_mm": 25.4,
      "hole": {
        "nominal_mm": 25.6,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "shaft": {
        "nominal_mm": 25.4,
        "tol_mm": [
          -0.102,
          0.102
        ]
      },
      "min_clearance_mm": -0.102,
      "max_clearance_mm": 0.502,
      "split_gap_mm": 1.2,
      "action": "split halves stand 0.6 mm off the centreline each side; when the screws close the gap the bore clamps before the halves touch for any printed bore error < 1.0 mm",
      "source": "boom OD tol as FT01; FDM bore tol +-0.2 mm (EST, well-tuned desktop FDM is +-0.1-0.3, Xometry desktop spec +-0.5 % lower limit +-0.5 mm, https://xometry.pro/en/articles/3d-printing-tolerances/)"
    },
    {
      "id": "FT03",
      "joint": "Landing leg 1.000 x 0.058 in in gear clamp socket (blind, 14.0 deep)",
      "nominal_mm": 25.4,
      "hole": {
        "nominal_mm": 25.7,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "shaft": {
        "nominal_mm": 25.4,
        "tol_mm": [
          -0.102,
          0.102
        ]
      },
      "min_clearance_mm": -0.002,
      "max_clearance_mm": 0.602,
      "action": "slip fit; ream or sand if tight; retained by F05 cross-bolt",
      "source": "as FT02"
    },
    {
      "id": "FT04",
      "joint": "Printed splice plug inside boom (rear motor mount), 80 mm long, 40 mm each tube",
      "nominal_mm": 23.622,
      "hole": {
        "nominal_mm": 23.622,
        "tol_mm": [
          -0.203,
          0.203
        ]
      },
      "shaft": {
        "nominal_mm": 23.2,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "min_clearance_mm": 0.019,
      "max_clearance_mm": 0.825,
      "action": "plug carries the cross-bolt crush load and aligns the tubes; cross-bolts carry axial and torsional load",
      "source": "boom ID 0.930 in (OnlineMetals pid 1211); tol from FT01 rule"
    },
    {
      "id": "FT05",
      "joint": "Spar socket tube in hot-wired/drilled foam channel, bonded",
      "nominal_mm": 25.4,
      "hole": {
        "nominal_mm": 26.0,
        "tol_mm": [
          -0.5,
          0.5
        ]
      },
      "shaft": {
        "nominal_mm": 25.4,
        "tol_mm": [
          -0.102,
          0.102
        ]
      },
      "min_clearance_mm": 0.098,
      "max_clearance_mm": 1.202,
      "action": "bond line filled with foam-safe adhesive (BOM line 'Foam-safe glue 4 oz')",
      "source": "channel tolerance EST (hand hot-wire); tube tol as FT01"
    },
    {
      "id": "FT06",
      "joint": "Joiner in wing saddle root-plate bores, slip fit (rev B)",
      "nominal_mm": 22.225,
      "hole": {
        "nominal_mm": 22.455,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "shaft": {
        "nominal_mm": 22.225,
        "tol_mm": [
          -0.102,
          0.102
        ]
      },
      "min_clearance_mm": -0.072,
      "max_clearance_mm": 0.532,
      "action": "SLIP FIT, NOT BONDED (CAD rev B, 2026-10-21): the joiner slides out of the saddle so the pod transport piece stays inside the R4 0.5 m envelope; with both panels bolted on (F09) it is captured between two printed Joiner_Stop discs bonded in the spar sockets at 300 mm from the root faces. Lap the joiner or drill the bore to 22.6 if tight",
      "source": "CAD bore = joinOD + 0.23 mm (cad/BuildVtol.cs WingSaddle); FDM tol EST; retention: cad/params.mjs Joiner_Stop"
    },
    {
      "id": "FT07",
      "joint": "Screw clearance holes in printed parts",
      "nominal_mm": 3.0,
      "hole": {
        "model_mm": "ISO 273 normal + 0.2: M2 2.6, M3 3.6, M5 5.7",
        "as_printed_mm": "ISO 273 normal: M2 2.4, M3 3.4, M5 5.5",
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "shaft": {
        "nominal_mm": 3.0
      },
      "min_clearance_mm": 0.2,
      "max_clearance_mm": 0.6,
      "action": "print a hole coupon first (M2); motor-pattern holes: drill to 3.4 after printing",
      "source": "ISO 273 H13 table (Albany County Fasteners chart, https://www.albanycountyfasteners.com/media/6b/b8/g0/1764944339/clearance-hole-chart.pdf); +0.2 mm compensation: https://pollen.am/design_for_3d_printing_holes"
    },
    {
      "id": "FT08",
      "joint": "ruthex M3 heat-set insert in printed hole",
      "nominal_mm": 4.0,
      "hole": {
        "nominal_mm": 4.0,
        "tol_mm": [
          -0.1,
          0.1
        ]
      },
      "shaft": {
        "nominal_mm": 4.6,
        "note": "insert knurl OD"
      },
      "min_clearance_mm": -0.7,
      "max_clearance_mm": -0.5,
      "action": "interference is intended (melt-in); tune the modelled hole on the coupon so the as-printed hole is 4.0",
      "source": "ruthex table (B08K1BVGN9 page); OD 3djake"
    },
    {
      "id": "FT09",
      "joint": "Lift prop 4 mm centre hole on X4110S shaft (dia 4, 0/-0.03)",
      "nominal_mm": 4.0,
      "hole": {
        "nominal_mm": 4.0,
        "tol_mm": null
      },
      "shaft": {
        "nominal_mm": 4.0,
        "tol_mm": [
          -0.03,
          0.0
        ]
      },
      "min_clearance_mm": null,
      "max_clearance_mm": null,
      "action": "prop hole tolerance not published (—); must slide on by hand",
      "source": "SunnySky X4110S drawing (https://cdn.shopify.com/s/files/1/2024/0305/files/X4110S.jpg?v=1553581346); JeeFly listing (https://www.amazon.com/dp/B0FJ21V736)"
    },
    {
      "id": "FT10",
      "joint": "APC 14x8.5EP 6.35 mm bore on 6 mm adapter shaft (dia 6, 0/-0.03)",
      "nominal_mm": 6.0,
      "hole": {
        "nominal_mm": 6.35,
        "note": "use the APC adapter ring that fits 6 mm; ring sizes not published (—)"
      },
      "shaft": {
        "nominal_mm": 6.0,
        "tol_mm": [
          -0.03,
          0.0
        ]
      },
      "min_clearance_mm": null,
      "max_clearance_mm": null,
      "action": "fit ring, check the prop runs true by spinning by hand",
      "source": "Motion RC LP14085EP listing (search 2026-10-21); SunnySky drawing"
    },
    {
      "id": "FT11",
      "joint": "Pusher motor cup in pod tail ring",
      "nominal_mm": 56.0,
      "hole": {
        "nominal_mm": 56.0,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "shaft": {
        "nominal_mm": 55.6,
        "tol_mm": [
          -0.2,
          0.2
        ]
      },
      "min_clearance_mm": 0.0,
      "max_clearance_mm": 0.8,
      "action": "4 radial F07 screws locate and retain",
      "source": "pod tail dia 60 mm (cad/params.txt tailR 0.030) less 2.0 mm wall (EST)"
    }
  ],
  "general_tolerances": {
    "printed_parts_default": {
      "rule": "+-0.5 % of size, lower limit +-0.5 mm (desktop FDM)",
      "source": "https://xometry.pro/en/articles/3d-printing-tolerances/ (checked 2026-10-21)"
    },
    "printed_parts_controlled": {
      "bores": "FT02/FT03",
      "insert_holes": "FT08",
      "motor_floor_thickness_mm": [
        4.35,
        4.65
      ],
      "motor_pattern_position_mm": "dia 0.2 to the motor pilot (fixed-fastener rule T = (H - F)/2 with H 3.4, F 3.0)",
      "other_hole_position_mm": "dia 0.4 (floating fastener T = H - F)"
    },
    "cut_tubes": {
      "class": "ISO 2768-m",
      "lengths": {
        "boom front 1045.4 (params segF; ISO 2768-m over 1000 up to 2000 mm, checked 2026-11-02)": 1.2,
        "boom stub 485.9": 0.8,
        "spar socket 800": 0.8,
        "joiner 760": 0.8,
        "leg 205": 0.5
      },
      "end_squareness_mm": 0.5,
      "cross_hole_position_from_end_mm": 0.3,
      "source": "ISO 2768-1 m column (https://amesweb.info/fits-tolerances/iso-2768-linear-dimensions-tolerances.aspx, checked 2026-10-21); squareness EST"
    },
    "torque_method": "No torque driver on hand: hang a known mass from a hex key, T = m g L (e.g. 0.6 N*m = 1.02 kg at L 60 mm). Makerspace torque driver is an assumption.",
    "hot_wired_foam": {
      "rule": "+-0.5 mm on hot-wired XPS sections, pockets and channels (EST, hand hot-wire); spar channel FT05 26.0 +-0.5",
      "source": "same basis as FT05 (channel tolerance EST, hand hot-wire); no measured hot-wire data (—); drawing DBF-DRW-001 rev F tolerance table (added 2026-11-03)"
    }
  },
  "unknowns": [
    "JeeFly 1755 hub thickness (sets F12 length)",
    "APC 14x8.5EP hub thickness and adapter ring sizes",
    "EMAX ES3005HV mounting-tab hole size and spacing; whether screws are supplied",
    "CoreWing F405 Wing V2 hole pattern: GetFPV says 30x30 mm but ArduPilot gives a 52 x 32 mm board, which cannot carry a 30 mm square of M3 holes",
    "Holybro PT40 pitot tube OD and MS5525 board hole spacing",
    "X4110S base-boss detail (drawing shows dia 5 x 0.9 at the base centre)",
    "Insert torque-out in PETG and PA6-CF (sets all insert torques)",
    "Bolt Depot shipping charge (shown only at checkout)"
  ]
}